Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2009 Kenworth T800, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles." Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2012 KENWORTH T2000, T660, T700, T800, AND W900, AS WELL AS MODEL YEAR 2009-2012 PETERBILT 365, 367, 384, 386, 387, 388, 389, AND 587 TRUCKS EQUIPPED WITH PACCAR MX ENGINES. THE OIL MODULE CENTRIFUGAL SPINNER FILTER CAP IN THE PACCAR MX ENGINE MAY BECOME LOOSE, POSSIBLY ALLOWING THE CAP TO COME OFF AND ENGINE OIL TO PARTIALLY DISCHARGE FROM THE OIL MODULE ONTO EXHAUST COMPONENTS. Remedy: DEALERS WILL RE-TORQUE THE OIL MODULE FILTER CAP AND INSTALL A SECONDARY RETENTION DEVICE ON THE SECONDARY CENTRIFUGAL SPINNER FILTER CAP. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING MARCH 2011. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 AND PETERBILT AT 1-940-591-4196.
PACCAR is recalling certain model year 2007-2014 Kenworth T800 and W900 trucks manufactured March 22, 2006, through July 15, 2013 and equipped with Primaax tridem rear suspensions and a pusher and/or tag axle. The affected trucks have brake chambers that take longer to apply or release the brakes than the required time limit. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 121, "Air Brake Systems." Remedy: PACCAR will notify owners, and dealers will modify the air brake system, free of charge. The recall began on January 15, 2014. Owners may contact PACCAR at 1-425-468-7400. Kenworth's recall number is 13KWL.
PACCAR IS RECALLING 140 MY 2005, 2007-2009 T800, W900, AND T660 TRUCKS. THE CALIPER MOUNTING FASTENERS ATTACHING THE AIR DISC BRAKE CALIPER ASSEMBLY TO THE TORQUE PLATE MAY HAVE RECEIVED INSUFFICIENT TORQUE DURING THE INSTALLATION PROCESS. THE INSUFFICIENT TORQUE MAY ALLOW THE AIR DISC BRAKE CALIPER ASSEMBLY TO BECOME LOOSE AND POSSIBLY SEPARATE FROM THE VEHICLE. Remedy: DEALERS WILL INSPECT AIR DISC BRAKE CALIPER ASSEMBLIES AND REPLACE THE CALIPER MOUNTING FASTENERS AND TORQUE PROPERLY. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE MANUFACTURER HAS NOT YET PROVIDED AN OWNER NOTIFICATION SCHEDULE. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
PACCAR IS RECALLING CERTAIN MODEL YEAR KENWORTH T660, T700, T800 AND W900 VEHICLES MANUFACTURED FROM DECEMBER 22, 2008, THROUGH AUGUST 2, 2010, AND EQUIPPED WITH AG400L AIR DISC BRAKES. THE AIR DISC BRAKE CALIPER COULD BE INSTALLED ON THE WRONG SIDE OF THE DRIVE AXLE POTENTIALLY CAUSING INTERFERENCE WITH THE SUSPENSION BRACKET AND THE REAR SUSPENSION AS THE OUTERMOST BRAKE PADS WEAR AND THE FLOATING CALIPER MOVES INBOARD. Remedy: DEALERS WILL VERIFY THE CORRECT ORIENTATION OF THE BRAKE CALIPER AND PERFORM THE NECESSARY REPAIR FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 24, 2010. OWNERS MAY CONTACT KENWORTH AT 425-828-5440.
KENWORTH IS RECALLING 9 MY 2009 T800S VEHICLES EQUIPPED WITH DANA FRONT AXLE. THE BRAKE SPIDER MOUNTING FASTENERS ATTACHING THE BRAKE SPIDER TO THE FRONT STEER AXLE FLANGE MAY HAVE RECEIVED INSUFFICIENT TORQUE DURING THE INSTALLATION PROCESS. THE INSUFFICIENT TORQUE MAY ALLOW THE BRAKE SPIDER FASTENERS AND BRAKE SPIDER TO BECOME LOOSE. Remedy: DEALERS WILL INSPECT AND REPLACE THE BRAKE SPIDER MOUNTING FASTENERS AND TORQUE THEM PROPERLY, AS WELL AS REVIEW THE BRAKE SPIDER AND STEER AXLE FLANGE HOLES FOR SIGNS OF VIBRATION AND FATIGUE AND REPLACE IF NECESSARY. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE MANUFACTURER HAS NOT YET PROVIDED AN OWNER NOTIFICATION SCHEDULE. OWNER MAY CONTACT KENWORTH AT 1-425-828-5440.
PACCAR IS RECALLING 130 MY 2004-2009 T2000, T800, T600, W900 AND T660 KENWORTH TRUCKS BUILT WITH AN AG400 REAR SUSPENSION, LONG STROKE BRAKE CHAMBERS, AND WIDE BASE TIRES (SUPER SINGLES). THESE VEHICLES MAY DEVELOP AN INCREASE IN LATERAL AND VERTICAL AXLE MOVEMENT. THIS MOVEMENT MAY CAUSE PART OR PARTS OF THE BRAKE ASSEMBLY (BRAKE CAM TUBE SUPPORT, BRAKE CHAMBER BRACKET, BRAKE CHAMBER, BRAKE SPIDER) TO DEVELOP FATIGUE CRACKS, POSSIBLY RESULTING IN THE FAILURE OF THE PART OR PARTS WITHIN THE BRAKE ASSEMBLY. Remedy: DEALERS WILL INSTALL THE CAM TUBE SUPPORT BRACKETS ON ALL OF THE REAR AXLE WHEEL ENDS. INSPECT THE REAR AXLE BRAKE ASSEMBLY AND REPLACE IT IF CRACKED. THE RECALL IS EXPECTED TO BEGIN DURING NOVEMBER 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440.
KENWORTH IS RECALLING 3,423 MY 2004-2009 T2000, T800,T600, W900 AND T660 VEHICLES. INCREASED BRAKE EXCITATION IN A CERTAIN VEHICLE CONFIGURATION WHICH INCLUDES BENDIX DRUM BRAKES, WIDE BASE LOW PROFILE SINGLE TIRES, AND AN AG400 OR AG460 REAR SUSPENSION, DUE TO ITS UNIQUE BRAKE CLOCKING AND CAM TUBE LENGTH, CAN CAUSE FATIGUE AND CRACKING TO BRAKE ASSEMBLY COMPONENTS. Remedy: DEALERS WILL INSPECT THE REAR AXLE BRAKES ASSEMBLY, REPLACE CRACKED REAR AXLE BRAKES ASSEMBLY COMPONENTS WHERE REQUIRED, AND INSTALL CAM TUBE SUPPORT BRACKETS ON ALL REAR AXLE WHEEL ENDS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN OR BEFORE JULY 25, 2009. OWNER MAY CONTACT KENWORTH AT 1-425-828-5440.
KENWORTH IS RECALLING MODEL YEAR 2009 THROUGH 2010 T2000, T800, T660 AND W900 TRUCKS MANUFACTURED BETWEEN NOVEMBER 12, 2008 AND SEPTEMBER 30, 2009. THE AXLE U-BOLTS ATTACHING THE AXLE TO THE SUSPENSION LEAF SPRING ON CERTAIN AG400L REAR SUSPENSIONS MAY HAVE RECEIVED INSUFFICIENT FASTENER TORQUE DURING THE INSTALLATION PROCESS. THE INSUFFICIENT TORQUE MAY ALLOW THE AXLE U-BOLT TO BECOME LOOSE, WHICH MAY CAUSE VIBRATION IN THE REAR SUSPENSION. Remedy: DEALERS WILL INSPECT THE AXLE U-BOLTS FOR VISIBLE DEFECTS, INCLUDING BENT AND/OR SMASHED THREADS AND RE-TORQUE THE AXLE U-BOLTS TO FACTORY SPECIFICATIONS. THE RECALL BEGAN ON NOVEMBER 4, 2009. OWNERS MAY CONTACT KENWORTH AT 425-828-5440.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2010 TRUCKS EQUIPPED WITH TRW STEERING SHAFTS. THE CIRCUMFERENTIAL WELD AROUND THE STEERING SHAFT TUBE THAT WELDS THE SPLINED TUBE TO THE NON-SPLINED TUBE MAY BE MISLOCATED. MISLOCATION OF THE CIRCUMFERENTIAL WELD MAY ALLOW THE SPLINED TUBE AND NON-SPLINED TUBE TO ROTATE RELATIVE TO ONE ANOTHER DURING A LOW SPEED, HIGH TORQUE TURN, POSSIBLY RESULTING IN A SEPARATION OF THE TWO TUBES. Remedy: DEALERS WILL INSPECT THE STEERING SHAFT USING A WELD PLACEMENT GAUGE PROVIDED BY TRW. ANY STEERING SHAFT FOUND TO HAVE BEEN WELDED IMPROPERLY WILL BE REPLACED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JULY 30, 2010. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4196.
PACCAR IS RECALLING MODEL YEAR 2008-2010 KENWORTH T300, T270, AND T370, MODEL YEAR 2009-2010 T800 AND PETERBILT MODEL YEAR 2008-2010 335, 340, AND 367 VEHICLES BUILT ON CUMMINS' DIESEL ENGINE. THE VEHICLES MAY BE DESIGNED WITH A HARD WIRED, DASH-MOUNTED SWITCH THAT ENABLES THE VEHICLE OPERATOR TO INHIBIT AFTERTREATMENT DIESEL PARTICULATE FILTER REGENERATION IN ENVIRONMENTS WHERE THE OPERATOR BELIEVES IT MAY BE UNSAFE FOR ELEVATED EXHAUST TEMPERATURES. DUE TO AN ISSUE WITH THE LOGIC IN THE ECM SOFTWARE IN THESE ENGINES, THE SWITCH MAY NOT FUNCTION CORRECTLY, LEADING THE OPERATOR TO BELIEVE THAT THE SWITCH IS IN "INHIBIT" MODE WHEN IT IS NOT. Remedy: PACCAR IS WORKING WITH CUMMINS TO REPAIR THE ENGINES FREE OF CHARGE PLEASE SEE 09E-046. THE SAFETY RECALL BEGAN ON OCTOBER 1, 2009. OWNERS MAY CONTACT CUMMINS AT 1-800-DIESELS (1-800-343-7357).
PACCAR IS RECALLING 263 MY 2008-2009 KENWORTH T800, W900 AND PETERBILT 365 AND 384 TRUCKS EQUIPPED WITH C7 OR C9 CATERPILLAR DIESEL ENGINES. THE FUEL PUMP OUTLET CHECK PLUG MAY BE CRACKED WHICH COULD CAUSE FUEL TO SPRAY AND LEAK. Remedy: PACCAR IS WORKING WITH CATERPILLAR (PLEASE SEE 08E042). CATERPILLAR WILL REPLACE THE FUEL PUMP PLUG FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING SEPTEMBER 2008. OWNERS MAY CONTACT CATERPILLAR AT-1-800-447-4986 OR KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 4,883 MY 2006-2009 KENWORTH T600, T660, T800, W900, T2000 AND MY 2008-2009 PETERBILT 365, 367, 379, 384, 386, 387, 388 AND 389 TRUCKS. INADEQUATE STIFFNESS OF THE DIESEL PARTICULATE FILTER (DPF) BRACKET COULD RESULT IN SEPARATION OF THE DPF FROM THE CHASSIS. Remedy: PACCAR IS WORKING WITH CATERPILLAR TO REPAIR THESE VEHICLES (PLEASE SEE 08E041). OWNERS MAY CONTACT CATERPILLAR AT 1-800-447-4986 OR KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 1,043 MY 2008-2009 KENWORTH C500, T2000,T660, T800 AND W900 TRUCKS EQUIPPED WITH BENDIX MV-3 DASH CONTROL VALVES. THE MOLDED VALVE BODY HAS AN INCORRECT CORE PIN IN THE INJECTION MOLD CAUSING THE VALVE BODY TO BE OVERSIZED IN THE DOUBLE CHECK VALVE AREA. THIS CONDITION CAN ALLOW THE RUBBER DOUBLE CHECK VALVE TO BECOME LODGED IN THE BODY OPENING UNDER CERTAIN CIRCUMSTANCES. Remedy: DEALERS WILL REPLACE THE BENDIX MV-3 DASH CONTROL VALVES FREE OF CHARGE. THE RECALL BEGAN ON APRIL 14, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-4196.
KENWORTH IS RECALLING 1,189 MY 2009 T2000, T600, T660, T800 AND W900 TRUCKS. THE AXLE U-BOLTS ATTACHING THE AXLE TO THE DRIVE BEAM ON CERTAIN AG380 REAR SUSPENSIONS MAY HAVE RECEIVED INSUFFICIENT FASTENER TORQUE DURING THE INSTALLATION PROCESS. Remedy: DEALERS WILL HAVE THE AXLE U-BOLT ON THE AFFECTED CHASSIS RE-TORQUED TO FACTORY SPECIFICATIONS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 12, 2008. OWNERS MAY CONTACT KENWORTH AT 425-828-5440.
PACCAR IS RECALLING 86 MY 2009 KENWORTH T660, T800, W900, AND PETERBILT 386, 365, AND 388 TRUCKS EQUIPPED WITH BENDIX FRONT AIR DISC BRAKES. THE SIZE 14 SERVICE CHAMBER OF CERTAIN FRONT AIR DISC BRAKES MAY HAVE BEEN CONTAMINATED WITH GREASE BETWEEN THE PISTON HEAD/PLATE AND THE DIAPHRAGM. WHEN BRAKING PRESSURE IS APPLIED, THE GREASE MAY ALLOW THE PISTON HEAD/PLATE TO SLIP OFF CENTER AND CATCH ON THE REDUCING RING OF THE SIZE 14 SERVICE CHAMBER. Remedy: DEALERS WILL REPLACE BOTH FRONT AIR DISC BRAKES SIZE 14 SERVICE CHAMBERS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 27, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 AND PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 2,096 MY 2009 KENWORTH AND PETERBILT VEHICLES EQUIPPED WITH TRW STEERING SHAFTS. MISLOCATION OF A CIRCUMFERENTIAL WELD MAY ALLOW THE SPLINED TUBE AND NON-SPLINED TUBE TO ROTATE RELATIVE TO ONE ANOTHER DURING A LOW SPEED, HIGH TORQUE TURN, POSSIBLY RESULTING IN A SEPARATION OF THE TWO TUBES. Remedy: DEALERS WILL INSPECT THE STEERING SHAFT USING A WELD PLACEMENT GAUGE AND MISWELDED STEERING SHAFT WILL BE REPLACED FREE OF CHARGE. THE RECALL BEGAN JULY 31, 2009. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 AND PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING 318 MY 2007-2009 KENWORTH T800, W900, AND PETERBILT 357, 365, 367, 378, 379, 384, 385, 386,388, AND 389 TRUCKS EQUIPPED WITH PREMIER TRAILER HITCH ASSEMBLIES. THE PINTLE HITCH ASSEMBLIES MAY HAVE BEEN MANUFACTURED IN A MANNER RESULTING IN A REDUCTION OF FATIGUE STRENGTH OF THE PIVOT PINS. Remedy: DEALERS WILL REPLACE THE POTENTIALLY DEFECTIVE PIVOT PIN FREE OF CHARGE. THE RECALL BEGAN ON APRIL 18, 2008. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4196.
PACCAR Incorporated (PACCAR) is recalling certain 2009-2021 Kenworth C500, 2012-2021 Kenworth T440, 2009-2015 Kenworth T660, 2015-2024 Kenworth T680, 2009-2024 Kenworth T800, 2009-2020 Kenworth T370, 2014-2023 Kenworth T880, 2011-2016 Kenworth T470, 2023 Kenworth T480, and 2009-2019 Kenworth W900 vehicles. The air tanks have an insufficient volume of air for the brake system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems." Remedy: Dealers will install the correct volume air tanks, free of charge. Owner notification letters were mailed August 12, 2024. Additional owner notification letters were mailed October 27, 2025. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 24KWD.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: On certain trucks, the welds that attach the trailer hitch may crack due to improper welding. As a result, the hitch could detach from the truck while towing a trailer. Note: This recall only affects certain trucks with trailer hitches installed by Commercial Truck Equipment. Safety Risk: A trailer that detaches from a truck could create a risk of a crash. Corrective Actions: Commercial Truck Equipment will notify owners by mail and instruct you to take your truck to a dealer to inspect the trailer hitch and repair or replace it, as necessary. You should stop using the trailer hitch until the inspection and repair have been completed.
Issue: On certain trucks, the warning light for the tractor anti-lock brake system (ABS) may not turn on if the system loses power. If this happens, the driver will not get warning that the ABS is not working properly. Note: This problem would also cause the traction control (TC) and electronic stability control (ESC) lights not to turn on. Safety Risk: If a driver is not warned that the ABS is not working properly, there could be an increased risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to update the software for the cab control module (CECU).
On certain trucks equipped with a Caterpillar C15 diesel engine, the Diesel Particulate Filter (DPF) combustion tube may fail. This could result in a vehicle fire causing property damage and/or personal injury. Correction: Dealers will replace the DPF combustion tube.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles equipped with a PACCAR MX engine, the oil module centrifugal spinner filter cap may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto nearby exhaust components. The discharge of engine oil onto hot exhaust components could result in a fire causing property damage and/or personal injury. Correction: Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap.
On certain vehicles equipped with the AG400L suspension and air disc brakes, a caliper could be installed on the wrong side of the drive axle. This could cause interference with the suspension bracket and U-bolts as the outermost brake pads wear and the floating caliper moves inboard. As this interference gets larger, it prohibits the movement of the floating caliper, subsequently reducing the outer pad's pressure on the disc which can eventually lead to reduced braking performance and increasing the risk of a crash. Correction: Dealers will inspect and, if necessary, replace one drive axle brake caliper.
On certain trucks, the weld around the steering shaft tube, which joins the splined tube to the non-splined intermediate tube, may be mislocated. An improperly located weld bead may allow the splined tube and non-splined tube to rotate relative one another during a low speed, high torque turn, resulting in a possible separation of the tubes. This could cause a loss of steering control which could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the steering shaft.
Certain vehicles may suffer cracking of various brake assembly components (i.e. brake cam tube mounting flanges, brake air chamber bracket, brake air chamber, brake spider). Over time, this cracking can cause a complete fracture of the cam tube, which could increase stopping distances and decrease parking brake hold capability. A reduction of braking capability could increase the risk of a crash causing property damage, personal injury or death. Correction: Dealers will inspect the rear axle brake assembly, replace cracked rear axle brake components where required, and install cam tube support brackets on all rear axle wheel ends.
On certain trucks, the rear axle u-bolts may have received insufficient tightening torque during vehicle assembly. This could allow the u-bolts to loosen over time, which may cause vibration in the rear suspension. If multiple fasteners were to become loose, the U-bolt holding the axle may lose clamp load and the rear axle may shift relative to the rear suspension drive beam, which might result in a crash causing personal injury or death. Correction: Dealers will tighten the axle u-bolts.
The emergency vehicle applications that are subject of this recall are designed with a dash-mounted switch that enables the vehicle operator to inhibit the aftertreatment diesel particulate filter regeneration in environments where the operator believes it may be unsafe for elevated exhaust temperatures. Due to an issue with the logic in the Electronic Control Module (ECM) software in certain vehicles, the switch may not function correctly, leading the operator to believe that the switch is in "inhibit" mode when, in fact, it is not. As a consequence, the operator may unknowingly permit hot exhaust gases to exit the vehicle tailpipe, increase the risk of melting or burning of nearby surfaces, or a fire, causing property damage, personal injury or death. Correction: Cummins dealers will upgrade the ECM software.
On certain vehicles, an incorrect weld on the steering shaft tube assembly may allow the splined tube and the non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes. This could result in a loss of steering control and a crash cause property damage, personal injury or death. Correction: Dealers will inspect and, if necessary, replace the steering shaft assembly.
On certain vehicles, the brake spider mounting fasteners attaching the brake spider to the front steer axle flange may have received insufficient torque during vehicle assembly. This could cause the brake spider fasteners and brake spider to become loose. If undetected, this could allow the fasteners to shear and fall either onto the roadway or into the drum brake assembly, allowing the brake to bind. Extended stopping distances may result in a vehicle crash causing property damage, personal injury or death. Correction: Dealers will inspect the brake spider fastener torque. If a defect is found, the brake spider mounting fasteners will be replaced.
On certain vehicles, the caliper mounting fasteners attaching the air disc brake caliper assembly to the torque plate may have received insufficient tightening torque during the assembly process. Insufficient torque may allow the caliper mounting fasteners and/or the caliper itself to become loose. This could cause the brake on the affected wheel end to become inoperable. Extended stopping distance could result in a vehicle crash causing property damage, personal injury or death. Correction: Dealers will replace caliper mounting fasteners and inspect the caliper assembly.
Certain vehicle configuration which includes an AG400 rear suspension, long stroke brake chambers, and wide base tires may develop an increase in lateral and vertical axle movement. This movement may cause part or parts of the brake assembly to develop fatigue cracks, possibly resulting in the failure of part or parts within the brake assembly. A failure may reduce vehicle brake performance, increasing the risk of a crash causing personal injury or death. Correction: Dealers will affect repairs.
On certain trucks equipped with a Caterpillar C9 diesel engine, the fuel pump outlet check plug may crack and cause fuel to spray and leak from the fuel pump which may create a fire hazard. Correction: Caterpillar dealers will replace the fuel pump plugs.
On certain trucks, the inadequate stiffness of the Diesel Particulate Filter (DPF) bracket could result in the separation of the DPF from the chassis, which could result in personal injuries or death to motorists or bystanders. Correction: Caterpillar dealers will replace bracket as necessary.