Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2010 BMW K1300 S, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
BMW IS RECALLING CERTAIN MODEL YEAR 2005-2011 MOTORCYCLES. THE BEARINGS COULD BE SUBJECT TO CORROSION. THIS COULD LEAD TO REDUCED MOVEMENT OF THE LINK LEVER. Remedy: BMW WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING MARCH 2011. OWNERS MAY CONTACT BMW AT 1-800-525-7417.
BMW IS RECALLING CERTAIN MODEL YEAR 2009 AND 2010 K1300 S AND K1300 GT MOTORCYCLES MANUFACTURED BETWEEN SEPTEMBER 11, 2008 AND NOVEMBER 19, 2009. POOR FUEL QUALITY MAY LEAD TO SMALL DEPOSITS WITHIN THE THROTTLE BODIES. DURING ENGINE OPERATION IN A LOW RPM RANGE, TYPICALLY NEAR IDLE SPEED (WHEN COMING TO A STOP) AIR FLOW COULD BE SUFFICIENTLY RESTRICTED AND ENGINE STALLING COULD OCCUR. Remedy: BMW WILL NOTIFY OWNERS AND REPAIR THE MOTORCYCLES BY UPDATING THE ENGINE MANAGEMENT SOFTWARE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON FEBRUARY 22, 2010. OWNERS MAY CONTACT BMW TOLL-FREE AT 1-800-831-1117.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: On certain motorcycles, the fuel pump flange could crack. If this happens, fuel could leak while the engine is running. Note: This recall only affects motorcycles that did not have the fuel pump replaced under Transport Canada recall 2013-442. Safety Risk: A fuel leak can create the risk of a fire. Corrective Actions: BMW will notify owners by mail and instruct you to take your motorcycle to a dealer to replace the fuel pump and auxiliary fuel pump (if equipped) with an improved version.
Certain motorcycles with dealer installed accessory turn signals may not comply with the requirements of Canada Motor Vehicle Safety Standard (CVMSS) 108 - Lighting System and Retroreflective Devices. The size of the lens on the accessory turn signals may be too small, and therefore would not meet the requirements of the standard. This could reduce vehicle conspicuity to following and approaching road users, and increase the risk of a crash causing injury and/or property damage. Correction: Dealers will replace the accessory turn signals with factory indicators that meet the requirements of the standard.
On certain motorcycles, the threaded holes on the rear wheel flange could crack if the wheel bolts are tightened beyond the specified torque limit during servicing. Over time, this could allow the bolts to back out of their threaded holes, causing the rear wheel to become loose. This could result in a loss of stability of the motorcycle, and increase the risk of a crash causing injury and/or property damage. Correction: Dealers will replace the aluminum rear wheel flange with a steel flange.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain motorcycles equipped with a Continental ContiSportAttack or ContiSportAttack2 front tire, a separation may develop between the thread, belt and carcass. This could potentially result in rapid air loss and/or tire failure, which could affect vehicle handling and increase the risk of a crash causing injury and/or property damage. Correction: Dealers will replace affected tires.
On certain motorcycles, cracks could develop in the fuel pump and/or auxiliary fuel pump flange (if equipped). This would result in fuel leaking when the engine is turned on and the fuel system is pressurized. Leaking fuel, in the presence of an ignition source, could lead to a fire causing injury and/or damage to property. Correction: Dealers will inspect the fuel pump flange(s) and install a reinforcing ring or replace the fuel pump(s), as necessary.
On certain motorcycles, due to environmental conditions, the bearings of the link lever attached to the rear strut could be subject to corrosion. This could lead to reduced movement of the link lever. Over time, if the corrosion became significant, restriction of movement of the link lever could occur. This could affect handling of the motorcycle. In an extreme case, this could result in the connecting rod breaking by a bending force, causing the rear wheel to decelerate by contact with the inner fender. This could lead to a crash depending on traffic, road conditions and rider's reactions. Correction: Dealers will replace the rear suspension relay lever.