Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2010 Infiniti QX56, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
NISSAN IS RECALLING CERTAIN FRONT AND REAR LOWER LINKS, P/NOS. 54501ZQ00A, 54500ZQ00A, 551A1ZQ00A, 551A0ZQ00A , 54501EA00A, 54500EA00A, 551A1EA500, 551A0EA500, 54501ZR00A, AND 54500ZR00A, SOLD BETWEEN NOVEMBER 25, 2009 AND MAY 14, 2010 AS REPLACEMENT PARTS FOR MODEL YEAR 2004 THROUGH 2010 TITAN, ARMADA, AND QX56, AND MODEL YEARS 2005 THROUGH 2010 FRONTIER, XTERRA, AND PATHFINDER VEHICLES. THE LOWER CONTROL LINK ASSEMBLY HAS TWO CYLINDRICAL COLLARS FORMING THE INBOARD ATTACHMENT POINTS TO THE CHASSIS. DUE TO AN IMPROPER WELDING PROCESS SOME COLLARS MAY CONTAIN WELDS THAT DO NOT MEET STRENGTH SPECIFICATIONS. Remedy: NISSAN WILL NOTIFY OWNERS AND DEALERS WILL REPLACE ANY AFFECTED LOWER LINK FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JULY 12, 2010. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.
NISSAN IS RECALLING CERTAIN MODEL YEAR 2010 TITAN, ARMADA, QX56, FRONTIER, XTERRA, AND PATHFINDER VEHICLES MANUFACTURED FROM NOVEMBER 19, 2009 THROUGH MARCH 3, 2010. THE LOWER CONTROL LINK ASSEMBLY HAS TWO CYLINDRICAL COLLARS FORMING THE INBOARD ATTACHMENT POINTS TO THE CHASSIS. DUE TO AN IMPROPER WELDING PROCESS SOME COLLARS MAY CONTAIN WELDS THAT DO NOT MEET STRENGTH SPECIFICATIONS. Remedy: NISSAN WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 20, 2010. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.
NISSAN IS RECALLING CERTAIN MODEL YEAR 2008-2010 TITAN, ARMADA, AND INFINITI QX56, AND MODEL YEAR 2008-2009 NISSAN QUEST VEHICLES. THE BRAKE PEDAL PIVOT PIN END WAS NOT SPIN-FORMED TO SPECIFICATION DURING THE MANUFACTURING PROCESS OF THE BRAKE PEDAL ASSEMBLY. THE PIVOT PIN COULD SLIDE AND CAUSE THE BRAKE PEDAL TO PARTIALLY DISENGAGE FROM THE BRAKE PEDAL BRACKET. Remedy: DEALERS WILL INSPECT TO SEE IF THE PIVOT PIN HAD BEEN FORMED PROPERLY AND WILL REPLACE THE BRAKE PEDAL ASSEMBLY IF NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 22, 2010. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 210.1 - User-ready Tether Anchorages for Restraint Systems. Specifically, the pictograms identifying the location of the tether anchors measure 15 mm in height instead of 20 mm as required by the Standard. Correction: Since this non-compliance condition does not pose any safety risk, no corrective action is required.
On certain vehicles, the lower control link assembly collars (forming the inboard attachment point to the chassis) may not have been manufactured correctly. If the collar weld fails, the cylindrical collar can open, which will allow the collar to slip over the mounting bolt and bushing. This may change the wheel camber, which could allow vehicle handling characteristics to deteriorate, possibly resulting in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the lower control link assembly.
On certain four-wheel drive vehicles, the joint portion of the front driveshaft may contain small cracks. These cracks may eventually lead to a failure, resulting in separation of the front driveshaft. If the driveshaft failed while the vehicle was moving, a loud noise would be heard. If the vehicle were in 2WD mode, the driveshaft would come to rest on the frame cross-member, and the vehicle could be operated normally. The driveshaft would not come in contact with brake, steering or fuel system components, therefore the risk of a crash is considered minimal. Correction: Dealers will inspect the vehicle and replace the front driveshaft if necessary.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the brake pedal pivot pin end was not properly manufactured. As a result, the pin may not remain in place, causing the brake pedal to partially disengage from the brake pedal bracket. If this occurs, the driver will experience unusual and noticeable looseness in the pedal and a reduction in braking force. A reduction in braking force may lead to increased stopping distances and the risk of a crash causing property damage, personal injury or death. Correction: Owners of all potentially affected vehicles will be contacted and their brake pedal assembly will be inspected and replaced if necessary.