Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2010 Peterbilt 320, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
PACCAR Incorporated (PACCAR) is recalling certain 1990-2020 Peterbilt 320 and 520 vehicles built with specific amber rear turn signals. The turn signals may also light up with the stop/tail lights when the brakes are applied. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Remedy: PACCAR will notify owners, and for trucks with rear amber lights, dealers will add a jumper harness between the chassis electrical harness and amber tail lights, free of charge. The recall began August 1, 2019. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 19PBC.
PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces. Remedy: Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.
PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2015 Peterbilt 320, 365, 367, 388, and 389 trucks manufactured July 21, 2008, to February 28, 2014. The front axle tie rod end clamp bolts may be improperly torqued. Remedy: PACCAR will notify owners, and dealers will replace the front axle tie rod assembly on any vehicle where the factory installed assembly has not been previously replaced, free of charge. Owners were mailed interim notices on May 11, 2015. The recall began on April 4, 2016. Owners may contact Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 215-C.
PETERBILT IS RECALLING CERTAIN MODEL YEAR 2010 320 TRUCKS EQUIPPED WITH HENDRICKSON HLR2 NON-STEERING PUSHER AXLE FOR FAILING TO COMPLY WITH REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." THE TRUCKS WERE NOT MANUFACTURED WITH THE REQUIRED NUMBER OF AIR TANKS FOR PROPER OPERATION OF THE VEHICLE'S BRAKE SYSTEM. Remedy: DEALERS WILL INSTALL AN ADDITIONAL AIR RESERVOIR TO THE AIR SYSTEM FREE OF CHARGE. THE RECALL BEGAN ON FEBRUARY 10, 2010. OWNERS MAY CONTACT PETERBILT AT 940-591-4196.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles equipped with Cummins Westport ISL-G engines, excessive engine crankcase pressure could cause the vent tube assembly elbow to detach from the breather. This could allow engine oil to come in contact with hot surfaces, increasing the risk of fire resulting in injury and/or damage to property. Correction: Dealers will install clamps at both ends of the elbow of the breather tube assembly and reprogram the Electronic Control Module (ECM) to improve diagnostic capabilities.
On certain vehicles, the tie rod end clamp bolts may not have been tightened to the correct specification. As a result, the tie rod ends could loosen, corrode, and eventually separate from the tie rod, resulting in a loss of steering control, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace tie rod assembly where the factory installed assembly has not been replaced.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain