Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2010 Peterbilt 386, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles." Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2012 KENWORTH T2000, T660, T700, T800, AND W900, AS WELL AS MODEL YEAR 2009-2012 PETERBILT 365, 367, 384, 386, 387, 388, 389, AND 587 TRUCKS EQUIPPED WITH PACCAR MX ENGINES. THE OIL MODULE CENTRIFUGAL SPINNER FILTER CAP IN THE PACCAR MX ENGINE MAY BECOME LOOSE, POSSIBLY ALLOWING THE CAP TO COME OFF AND ENGINE OIL TO PARTIALLY DISCHARGE FROM THE OIL MODULE ONTO EXHAUST COMPONENTS. Remedy: DEALERS WILL RE-TORQUE THE OIL MODULE FILTER CAP AND INSTALL A SECONDARY RETENTION DEVICE ON THE SECONDARY CENTRIFUGAL SPINNER FILTER CAP. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING MARCH 2011. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 AND PETERBILT AT 1-940-591-4196.
Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification." Remedy: Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2011-2012 KENWORTH T660, T700, AND T800 VEHICLES MANUFACTURED FROM APRIL 19, 2010, THROUGH MAY 13, 2011, AND MODEL YEAR 2008, 2010, AND 2011 PETERBILT 365, 367, 384, 386, 387, 388 AND 587 VEHICLES MANUFACTURED FROM APRIL 20, 2010, THROUGH JUNE 11, 2011, AND EQUIPPED WITH PACCAR MX ENGINES AND EATON ULTRASHIFT DM OR ALLISON AUTOMATIC TRANSMISSIONS (WITHOUT AUTO-NEUTRAL). THE FAST IDLE CONTROL MAY BE ACTIVATED BY THE OPERATOR WHILE THE TRANSMISSION IS IN GEAR. Remedy: KENWORTH AND PETERBILT DEALERS WILL UPDATE THE ENGINE SOFTWARE FOR THE AFFECTED CHASSIS. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 22, 2011. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 AND PETERBILT AT 1-940-591-4196.
PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2010 TRUCKS EQUIPPED WITH TRW STEERING SHAFTS. THE CIRCUMFERENTIAL WELD AROUND THE STEERING SHAFT TUBE THAT WELDS THE SPLINED TUBE TO THE NON-SPLINED TUBE MAY BE MISLOCATED. MISLOCATION OF THE CIRCUMFERENTIAL WELD MAY ALLOW THE SPLINED TUBE AND NON-SPLINED TUBE TO ROTATE RELATIVE TO ONE ANOTHER DURING A LOW SPEED, HIGH TORQUE TURN, POSSIBLY RESULTING IN A SEPARATION OF THE TWO TUBES. Remedy: DEALERS WILL INSPECT THE STEERING SHAFT USING A WELD PLACEMENT GAUGE PROVIDED BY TRW. ANY STEERING SHAFT FOUND TO HAVE BEEN WELDED IMPROPERLY WILL BE REPLACED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JULY 30, 2010. OWNERS MAY CONTACT KENWORTH AT 425-828-5440 AND PETERBILT AT 940-591-4196.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: On certain trucks, the warning light for the tractor anti-lock brake system (ABS) may not turn on if the system loses power. If this happens, the driver will not get warning that the ABS is not working properly. Note: This problem would also cause the traction control (TC) and electronic stability control (ESC) lights not to turn on. Safety Risk: If a driver is not warned that the ABS is not working properly, there could be an increased risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to update the software for the cab control module (CECU).
On certain trucks equipped with a PACCAR MX engine and Eaton Ultrashift DM or Allison automatic transmission (without auto-neutral), the Fast Idle Control (also known as high idle) may be activated by the operator while the transmission is in gear. This could override the parking brake, allowing the vehicle to move unexpectedly. Unintended vehicle movement could result in a crash causing property damage and/or personal injury. Correction: Dealers will update the engine control software.
On certain vehicles equipped with a PACCAR MX engine, the oil module centrifugal spinner filter cap may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto nearby exhaust components. The discharge of engine oil onto hot exhaust components could result in a fire causing property damage and/or personal injury. Correction: Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain trucks, the weld around the steering shaft tube, which joins the splined tube to the non-splined intermediate tube, may be mislocated. An improperly located weld bead may allow the splined tube and non-splined tube to rotate relative one another during a low speed, high torque turn, resulting in a possible separation of the tubes. This could cause a loss of steering control which could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the steering shaft.