Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2011 Infiniti M56, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Nissan North America, Inc. (Nissan) is recalling certain 2011-2013 Infiniti M56, 2012-2013 M35 Hybrid, and 2014 Q70 and Q70 Hybrid vehicles. These models, equipped with 2WD and with a hybrid or VK56 powertrain, have a driveshaft that may break. Remedy: Infiniti will notify owners, and dealers will replace the driveshaft, free of charge. The recall began February 5, 2021. Owners may contact Infiniti customer service at 1-800-662-6200.
Nissan North America, Inc. (INFINITI) is recalling certain 2011-2013 M56, 2012-2013 M35 Hybrid, 2014-2018 Q50, Q70 Hybrid, 2014-2019 Q70, and 2015-2019 Q70L two-wheel drive vehicles. The driveshaft can fatigue and break. Remedy: Dealers will replace the driveshaft, free of charge. Owner notification letters were mailed August 13, 2024. Owners may contact INFINITI's customer service at 1-800-662-6200. INFINITI's numbers for this recall are R24A5 and R24A7.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: On certain vehicles, the driveshaft may not have been manufactured properly. As a result, the driveshaft could break and cause a loss of power to the wheels. Additionally, if the vehicle is parked and the parking brake isn't applied, the vehicle could roll away. Note: This recall only affects two-wheel-drive (2WD) models. Safety Risk: A loss of power to the wheels could increase the risk of a crash. A parked vehicle that rolls away could also create the risk of an injury or a crash. Corrective Actions: Nissan will notify owners by mail and advise you to take your vehicle to a dealership to replace the driveshaft.
Issue: On certain vehicles, the propeller shaft (driveshaft) could break while driving and cause a loss of power to the wheels. In severe cases, a propeller shaft failure could also damage the parking brake. If this happens, there may be no way to stop movement of the vehicle when it is parked. This could allow the vehicle to roll away. Safety Risk: A loss of power to the wheels or a vehicle rollaway could increase the risk of a crash. Corrective Actions: The company will notify owners by mail and instruct you to take your vehicle to a dealer to replace the propeller shaft.
On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and the rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect the pressure sensor and tighten to specification. Note: This is an expansion of recall 2012-074. Vehicles that were repaired under the previous campaign are not affected because that remedy would have corrected the subject condition.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect for fuel leakage from the pressure sensor and the fuel rail. If there are no signs of a fuel leak, the fuel pressure sensor will be tightened to specifications. If a fuel leak is confirmed, the gasket between the sensor and the fuel delivery rail will be replaced, and the sensor will be tightened.