Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2011 Toyota RAV4, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2006-2011 Toyota RAV4 vehicles manufactured October 31, 2005, to September 7, 2010, and 2010 Lexus HS250h vehicles manufactured July 6, 2009, to August 26, 2010. The affected vehicles have rear suspension arms (rear tie rods) with adjusting lock nuts that may have been improperly tightened after servicing. As a result of being loose, the arm may have thread damage and may rust, possibly leading to the failure of the arm and an abrupt change in the vehicle's alignment. Remedy: Toyota will notify owners and dealers will replace both rear suspension arms and encapsulate the locknuts, free of charge. The recall began on September 30, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are G0V for Toyota vehicles and GLK for Lexus vehicles. Note: This recall supersedes recall 13V-383, in which some vehicles were only inspected, sealed, and did not have both arms replaced. The affected vehicles were previously recalled under 13V-383, but did not have both rear suspension arms replaced at that time. Those vehicles need to have both arms replaced as part of this recall remedy.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2009-2012 RAV4 vehicles manufactured October 27, 2008, to December 19, 2012 and 2012-2014 RAV4 EV vehicles manufactured July 24, 2012, to August 29, 2014. In the affected vehicles, water may drip onto the joint that connects the wiper linkage to the wiper motor. Remedy: Toyota will notify owners, and dealers will replace the water diverter channel. In addition, a new wiper linkage with a wiper motor crank arm will be installed. The wiper linkage will have a protective cover over the wiper linkage joint to minimize water splash and a retainer ring to prevent the wiper arm from separating from the wiper motor. The recall began on November 7, 2016. Owners may contact Toyota's customer service number at 1-800-331-4331.
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts. Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring. Remedy: SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed. Remedy: SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2006-2012 RAV4 vehicles manufactured July 28, 2005, to December 19, 2012, and 2012-2014 RAV4 EV vehicles manufactured July 24, 2012, to August 29, 2014. In the event of a frontal collision, the rear seat belts for the outboard seats may be cut by the seat cushion frame. Remedy: Toyota will notify owners, and dealers will install a protector over both rear seat cushion frames, free of charge. The recall began on June 24, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is G0F.
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed. Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2011 RAV4 VEHICLES, MANUFACTURED FROM NOVEMBER 24, 2011, THROUGH DECEMBER 19, 2011. IN THE CURTAIN SHIELD AIRBAGS, PROPELLANT WITH THE INCORRECT SPECIFICATION WAS USED FOR THE INITIATOR ASSEMBLED IN THE AIRBAG INFLATOR. IN THIS CONDITION, THE INFLATOR MAY NOT PERFORM PROPERLY, CAUSING ONE OR BOTH CURTAIN SHIELD AIRBAGS TO NOT DEPLOY. Remedy: TOYOTA WILL NOTIFY OWNERS, AND DEALERS WILL CHECK THE VEHICLE IDENTIFICATION NUMBER TO IDENTIFY THE CURTAIN SHIELD ASSEMBLIES AND REPLACE THE ASSEMBLIES AS NECESSARY WITH NEW ONES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 8, 2012. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust, leading to thread damage and eventual failure. Failure of the rear tie rod will cause an abrupt change in the vehicle's alignment. Remedy: Toyota will notify owners, and dealers will inspect the rear tie-rod nut for looseness and replace any suspect tie-rod found loose. Dealers will also affix instructions in multiple places to prevent improper servicing in the future. The recall began on November 30, 2012. Owners may contact Toyota at 1-800-331-4331 or Lexus at 1-800-255-3987.
Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust leading to thread damage and eventual failure. Failure of the rear tie rod will cause an abrupt change in the vehicle's alignment. Remedy: Toyota will notify owners, and dealers will inspect the tie rods and replace any that have rust or corrosion on the alignment adjustment threads. All of the rear tie rods will then be encased in an epoxy to prevent future environmental damage. Due to limitations in parts, the recall remedy will be launched in phases from September 2013 through mid-April 2014. All owners will receive notification of the recall, with most receiving second notifications when parts are available in their area. IMPORTANT: This recall supersedes Toyota and Lexus recall 12V-373. All vehicles that have been inspected and remedied under the previous recall need to be re-inspected and have the appropriate remedy applied.
Southeast Toyota is recalling certain model year 2008 and 2010-2013 Toyota Tundra, 2010-2012 Rav4, 2012 Toyota Sequoia, 2010-2011 Toyota Corolla, 2010-2011 Toyota Camry and Camry Hybrid, 2010-2013 Toyota Highlander and Highlander Hybrid, 2010-2013 Toyota FJ Cruiser, 2011 Toyota Land Cruiser, 2010-2013 Toyota Venza, 2010-2011 Toyota 4Runner, 2010-2013 Toyota Tacoma, 2011-2012 Toyota Sienna, 2012 Toyota Prius, 2013 Scion FR-S, 2011 Scion XD, 2011 Scion XB, and 2012 Scion TC vehicles. These vehicles were sold with labels that were outside the allowable one percent of accuracy of actual weight added. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 110, "Tire Selection and Rims." Remedy: Southeast Toyota will notify owners and provide a corrected label with instructions concerning its installation. A small group of the affected vehicles will need additonal remedies which are still being developed. The recall began on May 28, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.
On certain vehicles, the rear wheel suspension link arms could separate. This could result in loss of vehicle control and cause a crash resulting in injury and/or damage to property. Correction: Dealers will replace both suspension link arms and encase them in epoxy to prevent future improper servicing. Note: This recall supersedes recall 2013327. As part of the previous recall, dealers were to inspect the suspension arms for corrosion, replace them depending on their condition, and encase them in epoxy. Only vehicles which did not receive replacement of both suspension arms through the previous recall will need to be repaired under this campaign.
How cars of this model and year did at Norway's periodic inspection, across a full year of tests.
Source: Statens vegvesen, periodic inspections (EU-kontroll) · CC BY 4.0
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, in the event of a severe frontal collision, there is a possibility that the webbing of the seat belt in both second-row outboard seating positions could contact a portion of the metal seat cushion frame, become cut, and separate. If this occurs, the seat belt may not properly restrain the occupant, which could increase the risk of injury. Correction: Dealers will install plastic protectors on the seat cushion frame in both second-row outboard seating positions.
On certain vehicles equipped with a water channel located underneath the cowl louver at the base of the windshield and above the windshield wiper link assembly, due to stresses applied to the water channel during the manufacturing process, a section of the channel in some vehicles may become deformed and prevent water from draining properly. If water were to collect in the channel, it may drip onto the joint that connects the windshield wiper link and wiper motor. Over time, water dripping on this joint could result in corrosion and/or wear to the joint, which could result in the separation of the wiper link from the wiper motor crank arm. If separation were to occur, the windshield wipers could become inoperative, which could limit the driver’s visibility under certain operating conditions which may increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the water channel, the wiper link and wiper motor crank arm with ones of an improved design.
On some vehicles, if the rear wheel alignment toe adjustment locking nuts are improperly tightened when an alignment is performed in the field, backlash may develop in the threaded portion of the suspension arm (shaft and turnbuckle), followed by the formation of rust. If this occurs, threads may wear, causing the arm to separate which could result in loss of vehicle control. Correction: Dealers will inspect the suspension arm threads for corrosion. If corrosion is found, the arm(s) will be replaced. If no corrosion is found, an epoxy sealer will be applied to the suspension arm to inhibit corrosion. Note: This recall supersedes recall 2012253. Vehicles that were repaired under the previous campaign will also need to be repaired under this campaign.
This recall was replaced by Transport Canada recall no. 2013-327. On some vehicles, if the rear wheel alignment toe adjustment locking nuts are improperly tightened when an alignment is performed in the field, backlash may develop in the threaded portion of the suspension arm (shaft and turnbuckle), followed by the formation of rust. If this occurs, threads may wear, causing the arm to separate which could result in loss of vehicle control. Correction: Dealers will inspect the arms and verify the tightening torque of the lock nuts, or replace the arms, as necessary.
On certain vehicles, the side curtain airbag inflators may have been incorrectly manufactured and, as a result, one or both airbags may not deploy as intended. Failure of a side curtain airbag to deploy during a crash (where deployment is warranted), could increase the risk of personal injury to the seat occupant. Correction: Dealers will inspect and, if necessary, replace one or both side curtain airbag assemblies.