Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2011 Toyota Sienna, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2014-2016 Toyota 4Runner, 2014-2015 Scion xB, Lexus IS350C, IS250C, 2014 Toyota Sienna, Lexus IS-F, and 2014-2017 Lexus GX460 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Toyota is also recalling certain 2011-2013 Toyota Corolla, Corolla Matrix, Lexus IS250, IS350, 2011-2016 4Runner, 2011-2015 Scion xB, Lexus IS350C, IS250C, 2011-2014 Toyota Sienna, Lexus IS-F, 2011-2017 Lexus GX460, and 2011-2012 Lexus ES350 vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Toyota is also recalling certain 2010-2013 Toyota Corolla, Corolla Matrix, Lexus IS350, 2010-2016 4Runner, 2010-2013 Lexus IS250, 2010-2015 Scion xB, Lexus IS350C, IS250C, 2010-2017 Lexus GX460, 2010-2014 Lexus IS-F, and 2010-2012 Lexus ES350 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling. Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front passenger air bag inflator, or replace the air bag assembly. The recall began February 15, 2019. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are "Zone A" Toyota: G0P, Lexus: GLG; "Zone B" Toyota: G0R, Lexus GLH; "Zone C" Toyota: H0A, and Lexus: HLA.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling. Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2011-2016 Toyota Sienna minivans manufactured January 4, 2010, to August 12, 2016. If the power sliding door is unable to be opened when commanded, such as if the door is frozen shut, the door may subsequently open unexpectedly, possibly while the vehicle is moving. Remedy: Toyota will notify owners, and dealers will replace the junction block, rear sliding door wire harnesses, and install two sub wire harnesses, free of charge. The recall began on July 28, 2017. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is G04.
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring. Remedy: SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2008-2011 Scion xB and Lexus IS F, 2009-2011 Toyota Corolla and Corolla Matrix, 2006-2011 Toyota Yaris, Lexus IS250 and Lexus IS350, 2010-2011 Toyota 4Runner, Lexus IS250C, Lexus IS350C and Lexus GX460, 2011 Sienna, 2007-2011 Lexus ES350, and 2009-2010 Pontiac Vibe vehicles, originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain model year 2008 Scion xB and Lexus IS F, 2007-2008 Toyota Yaris, 2006-2008 Lexus IS250 and Lexus IS350 and 2007-2008 Lexus ES350 vehicles, originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles of these model years and models that were not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. Remedy: Toyota will notify the Toyota and Lexus owners. General Motors will contact the Pontiac owners. Depending on the model, dealers will replace the passenger frontal air bag inflator or the air bag assembly, free of charge. The recall began on December 6, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for interim notification for this campaign are G1P (Toyota Zone A), G1R (Toyota Zone B), G2G (Lexus Zone A), and G2H (Lexus Zone B). Toyota's numbers for final remedy for this campaign are G0P (Toyota Zone A), G0R (Toyota Zone B), GLG (Lexus Zone A), and GLH (Lexus Zone B).
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed. Remedy: SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2004-2011 Sienna vehicles originally sold in, or currently registered in, Connecticut, Delaware, Illinois, Indiana, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin and the District of Columbia. The affected vehicles have a spare tire carrier assembly mounted under the vehicle whose attachment cable may corrode due to high concentrations of road salt splashing onto the spare tire carrier. Remedy: Toyota sent owners in August 2014 an interim notification to advise owners of the recall and that dealers will perform an interim remedy to remove the spare tire and relocate it to the luggage compartment, free of charge. Owners are being mailed a second letter as parts become available and dealers will replace the spare tire carrier assembly with an improved one, free of charge. The remedy campaign is being performed in phases. The first phase of the recall began July 7, 2015. Owners may contact Toyota customer service at 1-800-331-4331. NOTE: 2004-2010 Siennas subject to this recall were subject to recall campaign 10V-160 initiated in 2010. Those owners are advised that they must have their vehicles remedied again under this campaign and that having the earlier recall completed did not remedy their vehicles. Additionally, model year 1998-2003 Siennas were recalled as part of safety recall 10V-160. Owners of those vehicles that have not had not the remedy performed on their vehicles, should contact their Toyota dealer to schedule a free repair.
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed. Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2011 THROUGH 2012 SIENNA VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NUMBER 110, "TIRE SELECTIONS AND RIMS." THESE VEHICLES DO NOT MEET THE REQUIREMENT FOR DISPLAYING THE CORRECT VEHICLE CAPACITY WEIGHT AS THE RATED LOAD FOR THE COMBINATION OF CARGO AND OCCUPANTS. Remedy: TOYOTA WILL NOTIFY OWNERS, AND WILL PROVIDE A REMEDY WHEN IT IS AVAILABLE. TOYOTA WILL MAIL OUT A CORRECTED PLACARD TO CUSTOMERS ALONG WITH REVISED OWNER MANUAL INFORMATION. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 27, 2013. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2010-2011 COROLLA VEHICLES EQUIPPED WITH A NON-TOYOTA, BLUE TOOTH HANDS FREE DEVICE OR NAVIGATION UNIT AND CERTAIN MODEL YEAR 2011 TOYOTA SIENNA VEHICLES EQUIPPED WITH A NON-TOYOTA, OVERHEAD ENTERTAINMENT SYSTEM AND/OR BLUETOOTH HANDS FREE DEVICE. THERE IS A POSSIBILITY THAT THE FRONT A-PILLAR TRIM PANEL RETENTION CLIP MAY HAVE BEEN DAMAGED DURING THE INSTALLATION OF THE AFTERMARKET ACCESSORY. Remedy: DEALERS WILL INSPECT THE A-PILLAR TRIM PANEL RETENTION CLIP AND REPLACE IT IF NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 30, 2011. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
Southeast Toyota is recalling certain model year 2008 and 2010-2013 Toyota Tundra, 2010-2012 Rav4, 2012 Toyota Sequoia, 2010-2011 Toyota Corolla, 2010-2011 Toyota Camry and Camry Hybrid, 2010-2013 Toyota Highlander and Highlander Hybrid, 2010-2013 Toyota FJ Cruiser, 2011 Toyota Land Cruiser, 2010-2013 Toyota Venza, 2010-2011 Toyota 4Runner, 2010-2013 Toyota Tacoma, 2011-2012 Toyota Sienna, 2012 Toyota Prius, 2013 Scion FR-S, 2011 Scion XD, 2011 Scion XB, and 2012 Scion TC vehicles. These vehicles were sold with labels that were outside the allowable one percent of accuracy of actual weight added. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 110, "Tire Selection and Rims." Remedy: Southeast Toyota will notify owners and provide a corrected label with instructions concerning its installation. A small group of the affected vehicles will need additonal remedies which are still being developed. The recall began on May 28, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2011 VENZA AND SIENNA PASSENGER CARS MANUFACTURED FROM MARCH 7, THROUGH MARCH 10, 2011. THERE IS A POSSIBILITY THAT THE FRONT, RIGHT, DRIVE SHAFT MAY BREAK DUE TO INSUFFICIENT HEAT TREATMENT. Remedy: TOYOTA WILL NOTIFY OWNERS AND DEALERS WILL INSPECT THE DRIVE SHAFT, AND, IF THE DRIVE SHAFT IS IDENTIFIED AS ONE THAT MAY NOT HAVE BEEN CORRECTLY MANUFACTURED, IT WILL BE REPLACED WITH A NEW ONE AT NO CHARGE. THE SAFETY RECALL BEGAN ON JUNE 22, 2011. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS. Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2011 SIENNA VEHICLES. THE BRAKE STOP LAMP SWITCH IS MOUNTED ON A SMALL BRACKET WELDED ON THE LEFT SIDE OF THE SERVICE BRAKE PEDAL SUPPORT ASSEMBLY. DUE TO ITS PROXIMITY TO THE PARKING BRAKE PEDAL, IN LIMITED CIRCUMSTANCES THE STOP LAMP SWITCH BRACKET COULD BE DAMAGED BY THE OPERATOR'S FOOT DURING PARKING BRAKE APPLICATION. Remedy: DEALERS WILL REPLACE THE BRACKET ASSEMBLY FREE OF CHARGE. TOYOTA PLANS TO MAIL AN INTERIM OWNER NOTIFICATION IN THE MIDDLE OF JANUARY 2011, TO ADVISE OWNERS OF THE RECALL. A SECOND LETTER WILL BE MAILED WHEN PARTS ARE AVAILABLE TO COMPLETE REPAIRS. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.
Issue: On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the passenger-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety Risk: If the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective Action: Owners will be notified by mail and instructed to take their vehicle to a dealer to have the passenger-front airbag inflator or airbag module replaced. Note: The Canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles equipped with power sliding doors, under certain conditions which impede the opening of the door (such as if the door becomes frozen with ice), the sliding door motor could stall when the door is operated. If the motor stalls, high current in the door motor circuit could be generated, operating the circuit protection for the door motor. If this occurs with the sliding door latch mechanism in an unlatched position, the door could open while driving, increasing the risk of injury to a vehicle occupant. Correction: Dealers will replace the existing junction block and the rear sliding door wire harnesses with newly designed ones. The dealer will also install two sub wire harnesses to connect the junction block to the two rear door wire harnesses.
On certain vehicles operated where road salts are frequently used, corrosion of the spare tire carrier assembly cable may cause the separation of the spare tire stowed under the vehicle. The spare tire falling on the road surface creates a safety hazard that may result in a crash causing injury and/or property damage. Correction: As an interim measure, dealers will remove the spare tire and store it in the cargo area of the vehicle. Dealers will replace the spare tire carrier assembly when parts become available. Note: This recall supersedes recall 2010-123. Vehicles that were inspected and/or repaired under the previous recall may still be at risk of spare tire separation and will require re-inspection and/or repair.
Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 110 - Tire Selection and Rims. The combined weight of occupants and cargo, as displayed on the Tire and Loading Information label, does not meet the requirements of the Standard. As such, the vehicle could be unwittingly overloaded, which would result in poor vehicle handling characteristics, increasing the risk of a crash causing property damage and/or personal injury. Correction: Dealers will install an updated Tire and Loading Information label, as well as an owner's manual overlay label. Customers with certain vehicles equipped with a genuine Toyota trailer hitch and 18” run flat tires or 19” wheels will be presented with an option (1) to remove the trailer hitch or (2) replace the tires (and rims) with new Extra Load Tires.
Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 210.2 - Lower Universal Anchorage Systems for Restraint Systems and Booster Cushions. The plastic buttons on the seatback of second row seats, which identify the location of the UAS anchor bars, may have been installed slightly outside the limits prescribed by the Standard. Correction: A production change has been undertaken to remedy the technical non-compliance. No corrective recall action is required as the technical non-compliance is deemed to be non-safety related.
On certain vehicles, the brake stop lamp switch is mounted on a bracket welded on the service brake pedal support assembly. This bracket is relatively close to the parking brake pedal when the parking brake pedal is fully applied. Due to its proximity to the parking brake pedal, in some instances, the stop lamp switch bracket could be damaged by the operator's foot. Depending on the amount of bracket deformation, this could result in the brake stop lamps remaining "ON". If the deformation is significant, the service brakes could become partially engaged, resulting in brake drag with associated brake noise, vibration and/or illumination of the brake warning light. Should the vehicle continue to be operated in this condition, brake drag could cause excessive heat, which may result in reduced braking performance. This could increase stopping distances, possibly resulting in a crash causing property damage and/or personal injury. Correction: Dealers will replace the service brake pedal support assembly.