Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2012 Freightliner Business Class M2, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Daimler Trucks North America, LLC (DTNA) is recalling certain 2012-2015 Freightliner Cascadia, Coronado, Business Class M2, 114SD, and Western Star 4900 trucks. In certain front axle, brake lining, and brake spider combinations, braking may cause high vibrations, resulting in early failure of the tie-rod tube. Remedy: DTNA will notify owners, and dealers will replace the brake linings, brake spider, and tie-rod, free of charge. The recall began March 22, 2019. Owners may contact DTNA customer service at 1-800-547-0712. DTNA's number for this recall is FL782.
Daimler Trucks North America LLC (DTNA) is recalling certain model year 2010-2017 Freightliner M2 Business Class, 108SD, 114SD, and Columbia trucks manufactured from January 6, 2010, through February 29, 2016, equipped with certain Bendix rear disk brakes and spring suspensions. The rear disk brake caliper may have been installed incorrectly, thus allowing the caliper to contact the suspension. Remedy: DTNA will notify owners, and dealers will correct the orientation of the rear brake calipers, as necessary, free of charge. The recall began on June 8, 2016. Owners may contact DTNA customer service at 1-800-547-0712. DTNA's recall number for this campaign is FL-705.
Daimler Trucks North America LLC (DTNA) is recalling certain model year 2011-2014 Cascadia, Business Class M2, Coronado, and Columbia Glider vehicles manufactured April 5, 2010, to June 15, 2013. The affected trucks are equipped with Fontaine Ultra LT Fifth Wheel connectors, which, due to cumulative damage to the fifth wheel and its locking mechanism, have a locking mechanism that may fail to operate or to properly engage. Remedy: DTNA will notify owners, and DTNA authorized service facilities will replace the fifth wheel with an Ultra NT model fifth wheel, free of charge. The recall began on November 20, 2015. Owners may contact DTNA customer service at 1-800-745-8000. DTNA's number for this recall is FL-692.
Daimler Trucks North America (DTNA) is recalling certain model year 2012-2013 Business Class M2, 108SD, 114SD vehicle chassis, manufactured from December 3, 2011, through October 12, 2012 and equipped with a SmartPlex switch hub module. Residue left over in the manufacturing process of the switch hub module may lead to intermittent shorts and energizing of certain switch hub module outputs. Remedy: DTNA will notify owners, and dealers will replace any of the affected modules free of charge. The recall began on April 29, 2013. Owners may contact DTNA at 1-800-547-0712.
DAIMLER TRUCKS (DTNA) IS RECALLING CERTAIN MODEL YEAR 2012-2013 FREIGHTLINER 108SD, BUSINESS CLASS M2, CASCADIA, CORONADO VEHICLES, EQUIPPED WITH A HALDEX QUICK RELEASE VALVE, AND MANUFACTURED FROM FEBRUARY 3, 2012, THROUGH MARCH 2, 2012. THE QUICK RELEASE VALVE COVER MAY NOT BE CORRECTLY MANUFACTURED, ALLOWING THE COVER TO BECOME SEPARATED FROM THE VALVE BODY. IF THE COVER SEPARATES FROM THE VALVE BODY, THE FRONT BRAKES MAY NOT FUNCTION. Remedy: DTNA WILL NOTIFY OWNERS, AND WHERE NECESSARY, THE QUICK RELEASE VALVE WILL BE REPLACED BY DTNA AUTHORIZED SERVICE FACILITIES, FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN BEFORE JUNE 15, 2012. OWNERS MAY CONTACT DTNA AT 1-800-547-0712.
DAIMLER TRUCKS (DTNA) IS RECALLING CERTAIN MODEL YEAR 2006-2013 FREIGHTLINER, STERLING, AND WESTERN STAR VEHICLES, EQUIPPED WITH DETROIT DIESEL EPA07 AND EPA10, DD13 AND DD15/16 ENGINES, MANUFACTURED FROM JANUARY 20, 2006, THROUGH FEBRUARY 20, 2012. THE PUMP TO RAIL HIGH PRESSURE FUEL LINE SUPPORT SYSTEM USED ON THESE ENGINES IS SENSITIVE TO ASSEMBLY TORQUE AND MAY BE DAMAGED DURING SERVICE WORK. AS A RESULT OF OTHER REPAIRS, THE LINE SUPPORTS MAY LOOSEN, POTENTIALLY LEADING TO FUEL LINE CRACKING AND A FUEL LEAK. Remedy: DTNA WILL NOTIFY OWNERS, AND WHERE NECESSARY, THE HIGH PRESSURE FUEL LINE SUPPORT SYSTEM WILL BE REPLACED BY DTNA AUTHORIZED SERVICE FACILITIES, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 27, 2012. OWNERS MAY CONTACT DTNA AT 1-800-547-0712.
DAIMLER TRUCKS (DTNA) IS RECALLING ONE 2012 CASCADIA AND CERTAIN MODEL YEAR 2012 AND 2013 FREIGHTLINER BUSINESS CLASS M2 VEHICLES, AND MODEL YEAR 2013 108SD AND 114SD VEHICLES MANUFACTURED FROM JANUARY 20, 2012, THROUGH FEBRUARY 17, 2012. CERTAIN PROPERTY CLASS 04 (PC04) STEERING WHEEL NUTS WITH INCOMPLETELY FORMED THREADS WERE SUPPLIED TO DTNA IN LIEU OF THE SPECIFIED PROPERTY CLASS 05 NUTS. THE STEERING WHEEL NUTS SUPPLIED MAY NOT PROVIDE THE CLAMP LOAD REQUIRED TO FULLY SEAT THE STEERING WHEEL ON THE STEERING SHAFT WHEN TIGHTENED TO THE SPECIFIED TORQUE. Remedy: DTNA WILL NOTIFY OWNERS, AND AFFECTED VEHICLES WILL HAVE A NEW STEERING WHEEL NUT INSTALLED BY DTNA AUTHORIZED SERVICE FACILITIES, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 21, 2012. OWNERS MAY CONTACT DTNA AT 1-800-547-0712.
Daimler Trucks North America (DTNA) is recalling certain model year 2009-2014 model year Freightliner Business Class M2 and Freightliner Custom Chassis MT45 and MT55 chassis manufactured August 27, 2008, through December 10, 2013 and equipped with Eaton hybrid automated transmissions. The software controlling the affected transmissions may improperly raise the vehicle's engine speed during downshifts without the driver's input. Remedy: DTNA will notify owners and dealers will update the hybrid transmission software, free of charge. The recall began on February 5, 2014. Owners may contact DTNA at 1-503-745-6910. DTNA's recall number is FL-657.
DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2011- 2012 BUSINESS CLASS M2 AND CORONADO TRUCKS MANUFACTURED FROM SEPTEMBER 1, 2010, THROUGH DECEMBER 31, 2010, EQUIPPED WITH A CUMMINS ISX OR ISL DIESEL ENGINE. THE V-BAND CLAMP ASSEMBLY, PART NUMBERS Q187684, Q187685, AND Q187686, USED TO CONNECT THE INLET AND OUTLET CONE SECTIONS TO THE DIESEL OXIDATION CATALYST (DOC)/DIESEL PARTICULATE FILTER (DPF) INCLUDE A T-BOLT WHICH CAN FRACTURE AND FAIL WHEN SUBJECTED TO STRESS OR LOAD. A FRACTURE OR FAILURE OF THE T-BOLT MAY CAUSE THE CLAMP TO LOOSEN AND THE INLET OR OUTLET SECTIONS ATTACHED TO THE DOC/DPF HOUSING TO DISCONNECT. Remedy: DAIMLER TRUCKS IS WORKING WITH CUMMINS TO IDENTIFY AND NOTIFY OWNERS OF THE RECALL CAMPAIGN. REPAIRS WILL BE PERFORMED BY AUTHORIZED CUMMINS DEALERS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 10, 2011. OWNERS MAY CONTACT CUMMINS AT 1-812-377-5000 OR DAIMLER TRUCKS AT 1-800-547-0712.
Daimler Trucks North America (DTNA) is recalling certain model year 2009-2012 Freightliner, Sterling, and Western Star vehicles manufactured from July 7, 2008, through December 15, 2011, and equipped with perpendicular air tank mounting brackets. The air tank mounting brackets may develop cracks which can lead to the air tank brackets separating from the frame rail. The air tanks may also separate from the vehicle. Remedy: DTNA will notify owners, and dealers will replace the air mounting brackets, free of charge. The recall began on December 24, 2012. Owners may contact Daimler Trucks North America toll free at 1-800-547-0712.
DAIMLER TRUCKS (DTNA) IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 FREIGHTLINER BUSINESS CLASS M2 AND WESTERN STAR 4900 EMERGENCY VEHICLES MANUFACTURED FROM JULY 2, 2010, THROUGH DECEMBER 13, 2011, EQUIPPED WITH A DD13 EPA10 DETROIT DIESEL ENGINE. THE ENGINE SHUTDOWN SOFTWARE NORMALLY PROVIDED TO PROTECT THE ENGINE AND VEHICLE MAY NOT HAVE BEEN DISABLED ON ENGINES INTENDED FOR EMERGENCY VEHICLE APPLICATIONS. Remedy: DTNA WILL NOTIFY OWNERS, AND DEALERS WILL DISABLE THE ENGINE SHUTDOWN SOFTWARE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 13, 2012. OWNERS MAY CONTACT DTNA AT 1-800-547-0712.
Daimler Trucks North America LLC (DTNA) is recalling certain 2006-2020 Freightliner Columbia, 2006-2021 Freightliner Business Class M2, 2007-2020 Freightliner Coronado, 2014-2021 Freightliner 122 SD, 2007 Sterling A 9500, 2006 Freightliner Argosy, 2006-2007 Sterling AT9500, 2008-2021 Freightliner Cascadia, 2006-2008 Freightliner Classic, 2006-2011 Freightliner Century Class, 2006-2010 Freightliner FLD, and 2017 Western Star 5700 vehicles. The rear reflective tape may be partially covered by the mudflap hanger bracket, which may reduce the vehicle's visibility to other drivers on the road. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Remedy: DTNA will notify owners, and dealers will inspect and reposition the reflective tape to ensure that it is completely visible, as necessary, free of charge. The recall began May 29, 2020. Owners may contact DTNA customer service at 1-800-547-0712. DTNA's number for this recall is FL848.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: Certain trucks were built with tires that are not approved for use with the truck's wheels. As a result, the tires may not perform properly, or a tire could fail. Safety Risk: A tire failure could cause a loss of control and increase the risk of a crash. Corrective Actions: Daimler Trucks North America (DTNA) will notify owners by mail. The corrective actions for this recall are under development. You will be instructed to bring your truck to a DTNA authorized service facility when a repair is available.
Issue: On certain trucks equipped with "Fleet Engineer" mud flaps, the bracket for the mud flaps may partially cover the rear reflective tape. Canadian regulations require that reflective tape must be visible on the rear of the truck. Safety Risk: Reflective tape that is covered may make the truck less visible to others and could create an increased risk of a crash. Corrective Actions: Daimler Trucks of North America (DTNA) will notify owners by mail and instruct you to take your truck to an authorized DTNA Service Facility to inspect the reflective tape. It will be moved as necessary to meet the regulations.
Issue: On certain trucks equipped with electronic stability control (ESC), the brake lights may turn on when the automatic traction control (ATC) activates. Canadian regulations do not allow brake lights to turn on when the automatic traction control activates. Safety Risk: Brake lights that turn on when a vehicle is not slowing could confuse other drivers. Corrective Actions: The company will notify owners by mail and instruct them to take their truck to a Daimler Trucks North America authorized service facility. The truck will either be reprogrammed or retrofitted so the brake lights do not turn on when the automatic traction control (ATC) activates.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Issue: Certain trucks were built with air reservoir tanks that are too small in relation to the size of the air brake chambers. Canadian regulations require enough air reservoir capacity to ensure the brakes work even with heavy use or when there is a partial loss of the air system. Safety Risk: Reduced braking could cause extended stopping distances and increase the risk of a crash. Corrective Actions: The company will notify owners by mail and instruct them to take their truck to a Daimler Trucks North America authorized service facility to modify the truck to ensure it meets Canadian regulations.
On certain trucks, a combination of brake vibrations and corrosion could cause the tie-rod tube to fatigue and break. This may lead to a disconnect between the front wheels and reduce the ability to steer the vehicle, which could increase the risk of a crash causing injury and/or damage to property. Correction: Daimler Trucks of North America Service Facilities will replace brake linings, brake spiders and tie rods as necessary.
On certain vehicles equipped with Kidde fire extinguishers with black plastic handles and valves, the fire extinguishers may become clogged or require excessive force to activate. Also, the nozzle may detach from the valve assembly with enough force that it could cause injury, and fail to discharge. In case of fire, failure of the extinguisher to function could result in injury and/or property damage. Correction: Owners will be provided with instructions on how to inspect the fire extinguisher to see if it is recalled. Replacement fire extinguishers will be supplied by Kidde directly. Note: For more information about recalled fire extinguishers, please visit <a href="https://inmarmarketaction.com/kidde/Kidde284CA/">www.kidde.com</a>.
On certain vehicles, the rear disk brake calipers may contact the spring suspension due to incorrect caliper orientation. This could reduce rear brake effectiveness which would result in increased stopping distances, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will correct the orientation of the rear calipers.
On certain vehicles equipped with Cummins Westport ISL-G engines, excessive engine crankcase pressure could cause the vent tube assembly molded rubber adapter to detach from the breather. This could allow engine oil to come in contact with hot surfaces, increasing the risk of fire resulting in injury and/or damage to property. Correction: Dealers will install clamps at both ends of the adapter of the breather tube assembly and reprogram the Electronic Control Module (ECM) to improve diagnostic capabilities.
On certain trucks fuelled by compressed natural gas, the exhaust tailpipe may terminate under the fuel tank cabinet. Over time, the continued heating of the fuel tank by exhaust gases could increase the risk of a fire, causing injury and/or damage to property. Correction: Dealers will install an exhaust pipe extension to relocate the tailpipe.
On certain vehicles equipped with Cummins ISL G or ISX12 G engines, incorrect engine ECU programming could cause the exhaust system temperature to become elevated during cold weather operation. This could also cause flames to be emitted from the exhaust. As a result, nearby combustible material could be ignited, increasing the risk of a fire, injury and/or damage to property. Correction: Authorized Cummins service facilities will update software programming.
On certain trucks equipped with Eaton Hybrid transmissions, a software defect could result in unintended acceleration while downshifting. This could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will update transmission control software.
On certain trucks, the customizable SmartPlex switch hub module may experience intermittent electrical shorts. As a range of equipment may have been connected to the switch hub module by final stage vehicle manufacturers; depending on vehicle configuration and intended use, these electrical shorts could have varied consequences. These may include the erratic operation of emergency, warning and/or work lights, the unexpected activation of a remote engine starter or the intermittent and/or uncontrolled operation of other body equipment. These or other malfunctions may result in an increased risk to road users, operators or bystanders. Correction: Dealers will inspect and, if necessary, replace the switch hub module.
On certain trucks, the air tank mounting brackets may crack, which could allow the tank to detach from the vehicle. An air tank separating from the vehicle could strike another vehicle, a stationary object, or a bystander. As well, loss of an air tank would cause a loss of service brakes, which could increase stopping distances, possibly causing a crash. These issues could result in property damage and/or personal injury. Correction: Dealers will replace the air tank mounting brackets.
On certain trucks, the quick release valve (QRV) cover may not have been welded correctly during manufacturing process and may become loose or separate from the valve body. If this occurs, air pressure may not be supplied to the front brakes during brake application. The rear brakes will continue to function. Reduction in braking efficiency could increase stopping distances, possibly resulting in a crash causing property damage and/or personal injury. Correction: Daimler authorized repair facilities will inspect and if necessary replace the quick release valve.
On certain vehicles, an incorrect steering wheel fastener may have been installed during vehicle assembly. The incorrect nut may not provide the clamp load required to fully seat the steering wheel onto the steering shaft. This could allow the steering wheel to wobble, which could hamper vehicle operation. If the problem is ignored, the nut could loosen completely, which could allow the steering wheel to detach from the steering shaft. These issues could result in a crash causing property damage and/or personal injury. Correction: Dealers will replace the steering wheel nut.