Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2016 Kenworth T680, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
PACCAR Incorporated (PACCAR) is recalling certain 2017-2018 Peterbilt 567 and 579 trucks and 2015-2018 Kenworth T660, T680, T800, T880 and W900 trucks. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles." Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on July 30, 2018. Owners may contact Peterbilt customer service at 1-918-259-3258 or Kenworth customer service at 1-425-828-5000.
PACCAR Incorporated (PACCAR) is recalling certain 2013-2019 Kenworth T680 and T880 and Peterbilt 579 trucks, greater than 30 feet long and equipped with side extender mounted intermediate marker lamp/turn signals that do not include a reflex reflector. Since both intermediate side marker lamps and reflex reflectors are required, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Remedy: PACCAR will notify owners and dealers will install reflex reflective tape, free of charge. The recall began January 15, 2019. Owners may contact PACCAR customer service at 1-918-259-3258. PACCAR's number for this recall is 18KWF, and 18PBC.
PACCAR Incorporated (PACCAR) is recalling certain 2016 Peterbilt 220, 320, 325, 330, 337, 348, 365, 367, 382, 384, 386, 389, 389G, 567, 579 and 587 trucks and Kenworth K170, T170, T270, T370, T440, T470,T660, T680, T800, T880, and W900 trucks equipped with certain Spicer D or E series steer axles. The castellated nut on the steer axles may not be properly torqued, allowing the tie rod to loosen. Remedy: PACCAR will notify owners, and dealers will inspect the torque of the castellated nut and tie rod, tightening it as necessary. If the tie rod stud and knuckle on units cannot be sufficiently torqued, the dealer will replace the knuckle and tie rod end assembly, free of charge. The recall began on November 13, 2017. Owners may contact Peterbilt customer service at 1-940-591-4000 or Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is P817-C.
PACCAR Incorporated (PACCAR) is recalling certain model year 2016 Kenworth T660, T680, T800, T880, and W900 trucks manufactured February 1, 2015, to April 20, 2015. During assembly, the affected vehicles did not undergo the rear wheel mounting torque verification process, and thus the rear wheels may be loose. Remedy: Kenworth will notify owners, and dealers will verify that the rear wheel lug nuts are correctly tightened, free of charge. The recall began on July 1, 2015. Owners may contact Kenworth customer service at 1-425-828-5000. Kenworth's number for this recall is 15KWG.
PACCAR Incorporated (PACCAR) is recalling certain model year 2015-2016 Kenworth T680 and T880 trucks manufactured November 17, 2014, to January 5, 2015. The affected vehicles are equipped with Meritor MT-40-14X rear drive axles that may circulate an inadequate amount of lubricant to the wheel end hub assembly. Remedy: Kenworth will notify owners, and dealers will replace the defective rear drive axle and inspect the wheel ends for damage, replacing them, as needed, free of charge. The recall began May 29, 2015. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 15KWB.
PACCAR Incorporated (PACCAR) is recalling certain 2015-2018 Kenworth K370, T680, T880 and 2017-2018 Peterbilt 567 and 579 trucks. The plastic fuel tee fittings on these trucks may leak fuel. Remedy: Kenworth and Peterbilt will notify owners, and dealers will replace the suspect fuel tees, free of charge. The recall began on April 13, 2017. Owners may contact Kenworth customer service at 1-425-828-5000 and Peterbilt customer service at 1-940-591-4000. PACCAR's numbers for this recall is 17KWA and 217-A.
PACCAR Incorporated (PACCAR) is recalling certain 2013-2017 Peterbilt 567 and 579 Kenworth T680 and T880 trucks equipped with optional spotlights. The spotlight circuit may not be adequately protected in the event of a short. Remedy: PACCAR will notify owners, and dealers will change the polyfuse switch in the spotlight circuit to a standard fuse, free of charge. The recall began on September 19, 2017. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 17KWC and 717-B.
PACCAR Incorporated (PACCAR) is recalling certain model year 2014-2016 Kenworth T660, T680, T880 trucks manufactured February 18, 2013, to April 10, 2015, and 2011-2016 Peterbilt 386, 389, 567, 579, and 587 trucks manufactured December 13, 2010, to April 20, 2015. The affected trucks, equipped with PACCAR MX-13 engines and Delco-Remy 40SI alternators, have alternator charge cables that may chafe against a formed metal freon discharge line. Remedy: PACCAR will notify owners, and dealers will reroute the alternator charge cable away from the metal freon line, free of charge. PACCAR issued an interim notification to owners on July 10, 2015. The recall began on September 16, 2015. Owners may contact Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. PACCAR's numbers for this recall are 15KWE and 515-F.
PACCAR Incorporated (PACCAR) is recalling certain model year 2011-2016 Kenworth T440, T470, T660, T680, and T880 trucks manufactured January 14, 2010, to May 22, 2015, and equipped with HID Headlamps and the option for Daytime Running Lamps (DRL). The DRLs are required to deactivate when the hazard warning lights are activated, however, the DRLs on these vehicles override the hazard flashing functionality after the brake pedal is pushed for more than two seconds. Normal hazard flashing functionality returns once the service brake is released. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108, "Lamps, Reflective Devices, and Associated Equipment." Remedy: Kenworth will notify owners, and dealers will update the cab controller software, free of charge. The recall began on September 167, 2015. Owners may contact Kenworth customer service at 1-425-828-5000. Kenworth's number for this recall is 15KWL.
Paccar Incorporated (Paccar) is recalling certain model year 2016 Kenworth T370, T660, T680, T800, T880, and W900 vehicles manufactured July 31, 2015, to August 12, 2015, and 2016 Peterbilt 337, 348, 365, 367, 382, 386, 389, 567, 579, and 587 vehicles manufactured August 4, 2015, to August 12, 2015. In the affected vehicles, the Engine Control Module (ECM) may short circuit, causing the engine to stall without warning. Remedy: PACCAR will notify owners, and dealers will replace the defective engine control modules, free of charge. The recall began on October 22, 2015. Owners may contact Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. Paccar's numbers for this recall are 15KWM (Kenworth) and 915-L (Peterbilt).
PACCAR Incorporated (PACCAR) is recalling certain model year 2016 Kenworth T440, T470, T660, T680, T800, T880, and W900 trucks manufactured February 16, 2015, to March 9, 2015. The affected vehicles are equipped with an SR-7 spring brake valve assembly that may have had the primary and secondary service brake applications installed in reverse. In the event of a failure in the primary or secondary circuit, the redundant circuit would not provide adequate service brake functionality. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 121, "Air Brake Systems." Remedy: Kenworth will notify owners, and dealers will inspect the vehicles and correct the air line installations as required, free of charge. The recall began on September 16, 2015. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 15KWK.
Paccar (Paccar Incorporated) is recalling certain 2016 Kenworth T680, T800, and T880 trucks manufactured January 5, 2015, to January 7, 2015 and 2016 Peterbilt 367, 384, 567, and 579 trucks manufactured January 2, 2015, to January 9, 2015 and equipped with Eaton Fuller FR 10-speed manual transmissions. In the affected vehicles, when the transmission shift lever is moved from reverse to neutral, the reverse gear may stay engaged. When the transmission shift lever is moved from reverse to a forward gear position, the transmission may mechanically lock because both the reverse gear and forward gear are simultaneously engaged. Remedy: Paccar will notify the owners, and dealers will inspect and repair the affected transmissions if necessary, free of charge. The recall began on December 4, 2015. Owners may contact Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. Paccar's numbers for this recall are 15KWM (Kenworth) and 1015N (Peterbilt).
PACCAR Incorporated (PACCAR) is recalling certain 2016-2021 Kenworth T680 trucks equipped with a 2.1m Cab and WABCO 6S/6M ABS brake system with drum brakes. The brake systems were manufactured with a standard rear-brake ABS modulator valve instead of a quick release valve, which may exceed the intended service-brake release timing. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems." Remedy: PACCAR will notify owners, and dealers will replace the standard rear-brake, ABS modulator valve with a quick release valve, free of charge. The recall began November 30, 2020. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 20KWD.
PACCAR Incorporated (PACCAR) is recalling certain 2016-2022 Peterbilt 567, 579, 2021-2022 Peterbilt 536, 2017-2021 Kenworth T880, 2016-2022 Kenworth T680, 2018-2020 Kenworth T440, 2020 Kenworth T270, and 2021 Kenworth T280 vehicles. The methane detection system will not function if the system loses power. Remedy: Dealers will re-wire the warning alarm, free of charge. Owner notification letters were mailed December 1, 2022. Owners may contact Peterbilt customer service at 1-940-591-4220, and Kenworth customer service at 1-425-828-5888. PACCAR's numbers for this recall are 21KWH and 21PBN.
PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles." Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.
PACCAR Incorporated (PACCAR) is recalling certain 2009-2021 Kenworth C500, 2012-2021 Kenworth T440, 2009-2015 Kenworth T660, 2015-2024 Kenworth T680, 2009-2024 Kenworth T800, 2009-2020 Kenworth T370, 2014-2023 Kenworth T880, 2011-2016 Kenworth T470, 2023 Kenworth T480, and 2009-2019 Kenworth W900 vehicles. The air tanks have an insufficient volume of air for the brake system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems." Remedy: Dealers will install the correct volume air tanks, free of charge. Owner notification letters were mailed August 12, 2024. Additional owner notification letters were mailed October 27, 2025. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 24KWD.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: Certain trucks were built with a standard rear brake ABS modulator valve instead of a quick release valve. This could result in an increased stopping distance. Note: This recall only affects certain trucks equipped with WABCO 6S/6M ABS brake systems and drum brakes. Safety Risk: An incorrect ABS modulator valve can cause increased stopping distances and increase the risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a Kenworth dealer to replace the standard rear brake ABS modulator valves with quick release ABS modulator valves.
Issue: On certain trucks, the warning light for the tractor anti-lock brake system (ABS) may not turn on if the system loses power. If this happens, the driver will not get warning that the ABS is not working properly. Note: This problem would also cause the traction control (TC) and electronic stability control (ESC) lights not to turn on. Safety Risk: If a driver is not warned that the ABS is not working properly, there could be an increased risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to update the software for the cab control module (CECU).
On certain trucks, the intermediate side marker lamp/turn signals do not comply with the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 108 - Lighting System and Retroreflective Devices. The intermediate side marker lamp/turn signals, mounted to the side extenders, do not include the required reflex reflectors. This could decrease vehicle conspicuity and potentially increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will install reflex reflective tape to the side extender near the intermediate side marker lamps.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, the castellated nut and cotter pin on the steer axle may not have been tightened to specification. This could cause the tie rod to become loose in the steer axle, which would result in audible noise and/or looseness in steering. If the vehicle were continued to be operated in this condition, the tie rod could disconnect from the knuckle, resulting in a complete loss of control of a vehicle wheel, which would increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect the torque of the castellated nuts on the tie rod, and replace the tie rod stud and knuckle as necessary.
On certain vehicles, the polyfuse for the spotlight could develop a short circuit in the cabin fuse box. A short circuit could result in overheating and melting of the fuse box, and could increase the risk of a fire causing injury and/or damage to property. Correction: Dealers will replace the optional polyfuse switch in the spotlight circuit with a standard fuse.
On certain vehicles equipped with 2017 emissions engines, a tee fitting in the fuel supply was improperly manufactured and could leak fuel. Leaking fuel, in the presence of an ignition source, could result in a fire causing injury and/or damage to property. Correction: Dealers will inspect and replace affected fittings as necessary.
On certain vehicles equipped with a Cummins engine, the Engine Control Module (ECM) could develop an internal electrical short circuit that could blow a fuse in the ECM’s electrical supply circuit. This could result in an unexpected engine stall without the ability to restart the engine, which could increase the risk of a crash. Correction: Dealers will replacing the existing, affected ECM with a new ECM.
Certain vehicles equipped with HID headlamps may not comply with the requirements of Canada Motor Vehicle Safety Standard 108 - Lighting System and Retroreflective Devices. A Daytime Running Lamp (DRL) that is optically combined with a turn signal lamp must switch off when the turn signal lamp is switched on as a hazard warning signal. In the affected vehicles, the DRL overrides the hazard flashing functionality after the service brake is applied for more than 2 seconds, which is contrary to the standard. The hazard functionality returns to normal when the application of the service brake is removed. Turn signal functionality would not impacted. Failure to warn oncoming vehicles with flashing hazard lamps could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will update vehicle software.
Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 121 - Air Brake Systems. The two service brake connections of the SR-7 spring brake valve assembly that provide the valve with feedback from the primary and secondary service brake applications may have been reversed during installation. Although the SR-7 valve would still function properly if there were normal reservoir pressure, in the event of a failure in the primary or secondary circuit, the redundant circuit would not provide adequate service brake functionality, and the vehicle would fail to meet the emergency brake system performance standard. This could result in reduced braking performance which could result in a vehicle crash. Correction: Dealers will inspect, remove and reconnect the air lines to the correct port of the SR-7 valve.
On certain vehicles, the wheel nuts may have been insufficiently tightened during vehicle assembly. This could cause the wheel nuts to loosen and could lead to a complete separation of the wheel(s) from the vehicle, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect, and properly tighten the lug nuts to specification.
On certain vehicles equipped with PACCAR MX-13 engines and Delco-Remy 40SI alternators, the alternator charge cable may chafe against an air conditioning discharge line. This chafing could lead to damage of the alternator cable's insulation and could lead to an electrical short, increasing the risk of fire, which could result in injury and/or damage to property. Correction: Dealers will rotate the alternator cable end 180 degrees to provide necessary clearance and reattach the cable to the alternator.
On certain vehicles, water could migrate into wiper motor head and could lead to internal corrosion. This internal corrosion could form a conductive salt bridge which could result in a short circuit, causing the wiper system to fail. Loss of windshield wiping capability, should it occur during a rainy/snowy day, may compromise the driver's ability to see the road and its users, and a short circuit could increase the risk of fire, which could result in injury and/or damage to property. Correction: Dealers will install a shield over the wiper motor to protect it from water intrusions and prevent corrosion.