Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2016 Mazda CX-3, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Mazda North American Operations (Mazda) is recalling certain model year 2010-2013 Mazda3 and Mazdaspeed3 vehicles manufactured November 18, 2008, to June 8, 2013, 2012-2015 Mazda5 vehicles manufactured October 26, 2010, to June 22, 2015, 2016 CX-3 vehicles manufactured June 1, 2015, to December 26, 2015, and 2013-2016 CX-5 vehicles manufactured December 15, 2011, to December 26, 2015. On the affected vehicles, the lift gate support struts may corrode, possibly causing the struts to break and/or the lift gate to drop unexpectedly. Remedy: Mazda dealers will replace the both lift gate supports, free of charge, however parts are not currently available. The recall began April 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9916H.
Mazda North American Operations (Mazda) is recalling certain model year 2016 CX-3 vehicles manufactured June 1, 2015, to December 2, 2015, 2013-2014 Mazda2 vehicles manufactured July 3, 2013, to August 8, 2014, 2014-2016 CX-5 vehicles manufactured January 19, 2013, to December 2, 2015, and 2013-2015 CX-9 vehicles manufactured December 6, 2012, to July 31, 2015. The lower mounting nuts and bolts that attach the front strut assembly to the steering knuckle may loosen, allowing the steering knuckle to separate. Remedy: Mazda will notify owners, and dealers will inspect the lower mounting nuts and bolts that secure the front strut assembly to the steering knuckle. If the bolts are loose, they will be replaced and then correctly tightened, free of charge. The recall is expected to begin May 20, 2016. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9316D.
Mazda North American Operations (Mazda) is recalling certain 2014-2018 Mazda3 and 2016-2021 CX-3 vehicles. The rearview camera image may not display properly by showing a flickering or distorted image. Remedy: Dealers will inspect and replace the rearview camera, as necessary. In addition, dealers will install a wiring harness fastening seal. All repairs will be performed free of charge. Interim notification letters, notifying owners of the safety risk, were mailed September 13, 2023. Final owner letters for affected models and model years in the states of CT, MA, MD, NJ, NY, PA and VA were mailed August 14, 2024. The remaining owner notification letters will be mailed at a future date, anticipated on or before May 1, 2025. Owners may contact Mazda customer service at 1-800-222-5500, Option 6. Mazda's number for this recall is 6023G.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Issue: On certain vehicles, a problem with the rearview camera connector could cause distortion or flickering of the rearview camera image. Note: This recall only affects hatchback (5-door) models. Safety Risk: A rearview camera image that doesn't display correctly could reduce a driver's ability to see behind the vehicle while backing up. This could increase the risk of a crash. Corrective Actions: Mazda will notify owners by mail and advise you to take your vehicle to a dealership to inspect the rearview camera and install a seal for the wiring harness. The dealer will replace the rearview camera, if necessary.
On certain vehicles, the anti-corrosion treatment of the outer tube of the rear lift gate stay may be insufficient. Over time, the outer tube of the rear lift gate stay may corrode and break off, which could increase the risk of injury. Correction: Dealers will replace both rear door stays.
On certain vehicles, the nut and bolt holding the strut assembly to the knuckle may not have been tightened properly during the manufacturing process. Over time, this could cause the strut assembly to separate from the knuckle, resulting in a loss of steering control which would increase the risk of a crash causing injury and/or damage to property. Correction : Dealers will inspect and replace the nut and bolt holding the strut assembly to the knuckle if found loose.
How cars of this model and year did at Norway's periodic inspection, across a full year of tests.
Source: Statens vegvesen, periodic inspections (EU-kontroll) · CC BY 4.0
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain