Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2016 Pierce Saber, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Pierce Manufacturing (Pierce) is recalling certain model year 2015-2016 Arrow, Dash, Enforcer, Impel, Quantum, Saber, and Velocity fire trucks manufactured June 29, 2015, to June 30, 2016. The affected vehicles may be equipped with certain C20 and C21 split-shaft transmissions from Waterous. This transmission sends power to the wheels of an emergency response vehicle or power to an add-on unit such as a water pump used for fighting fires. A component within the shift unit may be damaged and as a result, the operator may not be able to switch the power output. Remedy: Piece will notify owners, and dealers will remove the shift unit assembly and replace the clevis pin and retaining rings, free of charge. The recall began on September 2, 2016. Owners may contact Pierce customer service at 1-888-974-3723. Pierce's number for this recall is 74B277.
Pierce Manufacturing (Pierce) is recalling certain 2015-2016 Arrow XT, Enforcer, Impel, Quantum, Saber, and Velocity vehicles, equipped with certain Spicer D-Series and E-Series steer axles. The castellated nut on the steer axles may not be properly torqued, allowing the tie rod to loosen. Remedy: Pierce will notify owners, and dealers will inspect the torque of the castellated nut and tie rod, tightening it as necessary. If the tie rod stud and knuckle on units cannot be sufficiently torqued, the dealer will replace the knuckle and tie rod end assembly, free of charge. The recall began on November 30, 2017. Owners may contact Pierce customer service at 1-414-832-3000.
Pierce Manufacturing (Pierce) is recalling certain 2015-2016 Arrow XT, Enforcer, Quantum, Saber, Velocity, and Commercial emergency vehicles equipped with Hale pressure relief valves in the water pumps used for fire fighting. Rings securing the valves may corrode over time after exposure to water, causing the ring to fail and the pressure relief valve to open, reducing the water pressure available for fire fighting. Remedy: Pierce has notified owners, and dealers will install a remedy kit, free of charge. The recall began on February 9, 2018. Owners may contact Pierce customer service at 1-888-974-3723 or Hale Products at 1-800-533-3569. Pierce's number for this recall is 74B287.
Pierce Manufacturing (Pierce) is recalling certain model year 2016 Arrow-XT, Dash, Enforcer, Impel, Quantum, Saber, and Velocity fire and emergency vehicles manufactured October 13, 2015, to February 9, 2016. The fastener cap over the bearing on the universal joint of the drive shaft may have been improperly tightened. Remedy: Pierce will notify owners, and dealers will check and correct the tightness of all bolts for the universal joint caps, as needed, free of charge. The recall began on March 25, 2016. Owners may contact Pierce customer service at 1-888-974-3723. Pierce's number for this recall is 74B270.
Pierce Manufacturing (Pierce) is recalling certain model year 2015-2016 Arrow XT, Velocity, Enforcer, and Saber vehicles manufactured November 20, 2014, to September 29, 2015. The affected vehicles are equipped with front drive axles whose hex nuts on the flange yoke may not have been properly tightened. Remedy: Pierce will notify owners, and dealers will inspect the hex nuts, tightening them as necessary, free of charge. The recall began on November 12, 2015. Owners may contact Pierce customer service at 1-888-974-3723. Pierce's number for this recall is 74B266.
Pierce Manufacturing (Pierce) is recalling certain model year 2015-2016 Arrow XT, Enforcer, Impel, Quantum, Saber, and Velocity emergency vehicles manufactured August 4, 2015, to August 24, 2016, equipped with pumps to provide pressurized water to aid in fighting fires. These pumps have 6" intake strainers that may have been improperly soldered during production and, as a result, the strainers may come apart during use, allowing parts of the strainer and debris to enter the pump, possibly damaging the pump. Remedy: Pierce will notify owners to check the strainer for missing solder at the joints. Any strainers missing solder will be replaced, free of charge. The recall began on June 16, 2016. Owners may contact Pierce customer service at 1-888-974-3723 or Hale Products Customer Service Center at 1-800-533-3569. Pierce's number for this recall is 74B272.
Pierce Manufacturing (Pierce) is recalling certain model year 2014-2016 Enforcer and Saber emergency vehicles manufactured from March 3, 2014, through February 3, 2016. The clamps on the heater hose may have been improperly installed allowing engine coolant to leak into the passenger compartment. Remedy: Pierce will notify owners, and dealers will inspect the hose clamp installation. Any improperly installed clamps will be corrected free of charge. The recall began on April 11, 2016. Owners may contact Pierce customer service at 1-888-974-3723. Pierce's number for this recall is 74B269.
Pierce Manufacturing (Pierce) is recalling certain 2016-2018 Enforcer, Freightliner and Saber vehicles equipped with ECCO Holdings Code 3 7x9 Stop-Tail-Turn Reverse All-in-One LED stop, tail, turn, and reverse lights. The rear LED lights may be too bright. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment." Remedy: Pierce will notify owners, and dealers will provide a filter kit to be installed in the rear lights, free of charge. The recall is expected to begin April 26, 2021. Owners may contact Pierce customer service at 1-888-974-3723.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
Certain vehicles may have driveshaft universal joint bearing cap fasteners that were not properly tightened at the time of assembly. This could allow bearing caps to detach from the vehicle and become a road hazard. Additionally, this could cause the universal joint to separate causing a loss of motive power which could increase the risk of a crash causing injury and/or damage to property. Correction : Dealers will inspect and retighten the fasteners as necessary.
Certain vehicles may have improperly installed heater core hose clamps which could allow engine coolant to leak into the passenger compartment and come in contact with electrical components. This could result in an electrical short, causing the vehicle to lose power and increasing the risk of a crash causing injury and/or damage to property. Hot coolant could also come in contact with the occupants of the vehicle and cause burn injuries. Correction: Dealers will inspect and reinstall the hose clamps properly.
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain