Loading NHTSA data…
Loading NHTSA data…
Recalls, inspection results and owner complaints for the 2011 Nissan Juke, from official sources in the US, Canada and Europe. To check one specific car, enter its VIN or plate.
We checked recall campaigns for this vehicle, or for its model where the register works by model.
Source: NHTSA (US Department of Transportation) · US public domain
Nissan North America, Inc. (Nissan) is recalling certain 2011-2012 Nissan Juke vehicles previously remedied under recall 12V-069. During that recall remedy, the fuel pressure sensor may not have been properly tightened, potentially causing the sensor to loosen and leak fuel. Remedy: Nissan will notify owners, and dealers will tighten the fuel pressure sensor to the proper torque, free of charge. The recall began on April 24, 2018. Owners may contact Nissan customer service at 1-800-867-7669.
NISSAN IS RECALLING CERTAIN MODEL YEAR 2011 NISSAN JUKE VEHICLES MANUFACTURED FROM APRIL 9, 2010, THROUGH MAY 12, 2011. THE TURBOCHARGER BOOST SENSOR BRACKET MAY SEPARATE FROM THE AIR INLET TUBE DUE TO A DEFECTIVE WELD. Remedy: NISSAN WILL NOTIFY OWNERS, AND DEALERS WILL CHECK THE LOT NUMBER ON THE AIR INLET TUBE AND REPLACE IT IF NECESSARY, FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR ABOUT JANUARY 9, 2012. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.
NISSAN IS RECALLING CERTAIN MODEL YEAR 2011-2012 JUKE, INFINITI QX AND INFINITI M VEHICLES. THE FUEL PRESSURE SENSORS MAY NOT HAVE BEEN TIGHTENED TO THE CORRECT SPECIFICATION. AS A RESULT, THE FUEL PRESSURE SENSOR MAY LOOSEN DUE TO HEAT AND VIBRATION CAUSING FUEL TO LEAK. Remedy: NISSAN WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE FUEL PRESSURE SENSORS, AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT NISSAN CUSTOMER SERVICE AT 1-800-647-7261.
We checked Transport Canada's recall database for this make, model and year.
Source: Transport Canada Vehicle Recalls Database · Open Government Licence – Canada
On certain vehicles, the fuel pressure sensor may not have been tightened properly when the corrective measure of recall 2012-074 was performed. As a result, the fuel pressure sensor may loosen over time, which could cause a fuel leak. A fuel leak in the presence of an ignition source could result in a fire causing injury and/or damage to property. Correction: Dealers will inspect and retighten the fuel pressure sensor as necessary.
On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and the rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect the pressure sensor and tighten to specification. Note: This is an expansion of recall 2012-074. Vehicles that were repaired under the previous campaign are not affected because that remedy would have corrected the subject condition.
On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect for fuel leakage from the pressure sensor and the fuel rail. If there are no signs of a fuel leak, the fuel pressure sensor will be tightened to specifications. If a fuel leak is confirmed, the gasket between the sensor and the fuel delivery rail will be replaced, and the sensor will be tightened.
How cars of this model and year did at Norway's periodic inspection, across a full year of tests.
Source: Statens vegvesen, periodic inspections (EU-kontroll) · CC BY 4.0
Problems owners of this model reported to NHTSA, grouped by component.
Source: NHTSA (US Department of Transportation) · US public domain
Crash-test ratings from NHTSA's New Car Assessment Program.
Source: NHTSA (US Department of Transportation) · US public domain
On certain vehicles, a weld at the boost sensor bracket may fail, allowing the bracket to separate from the air inlet tube. If this occurred, the engine would enter fail-safe driving mode, resulting in reduced motive power in which the vehicle could still be driven for short distances. Continued operation could cause the engine to stall which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the air inlet tube assembly.